At LEVOLOR, our legacy of quality of product and quality of service is our top priority. Even during these challenging times, we are here to provide inspiration or help with your next design project.
The following illustrations show installed examples of some common valance styles. Refer to the installation that matches your valance.
Designline™ Valance
Traditional Valance
Transitional Valance
Visions™ Faux Wood Valance
Before you begin:
Please refer to the illustrated examples to determine which clips and instructions you will need.
Twist-lock Valance Clips
Visions™ Valance Clips
Installing Valance Clips
Step A
Install the valance clips—DesignLine™, Traditional, and Transitional (outside-mount)
NOTE: Headrail mounting shown in installed position to show typical mounting bracket locations.
Position one clip at each end of the headrail next to the headrail mounting bracket locations. Make sure that the clips do not interfere with the mounting brackets.
Lower the clip into the top channel of the headrail at 45° angle to the headrail so the locking tabs fit into the channel.
Rotate the clip in the channel so that it locks into place.
Space remaining clips evenly between the ends, not more than 30" apart.
Step B
Install the valance clips—DesignLine™, Traditional, and Transitional (inside-mount)
NOTE: Valance clips must be installed prior to headrail installation.
Position one clip at each end of the headrail, next to the headrail mounting bracket locations. Make sure that the clips do not interfere with the mounting brackets.
Lower the clip into the top channel of the headrail at a 45° angle to the headrail so the locking tabs fit into the channel.
Rotate the clip in the channel so that it locks into place.
DesignLine™ Outside- and Inside- Mount Installation
Tailored Edge
Step 1
Attach the valance to the headrail
Center the front panel with the headrail.
Slide the mounting tab on the front valance panel into the valance clips until they click into place.
Step 2
Attach the returns (outside-mount)
Slide the end of the return into the pocket of the corner clip, as shown.
Slide the corner clip onto the end of the front panel. The top notch will slide over the mounting tab; the lower lip on the bottom notch will slide into the channel on the back of the lower front panel trim.
Repeat for the other return.
Round Edge
Step 1
Attach the valance to the headrail
Center the front panel with the headrail.
Slide the mounting tab on the front valance panel into the valance clips until they click into place.
Step 2
Attach the returns (outside-mount)
Slide the end of the return into the pocket of the corner clip, as shown.
Slide the corner clip onto the end of the front panel. The top notch will slide over the mounting tab; the lower lip on the bottom notch will slide into the channel on the back of the lower front panel trim.
Repeat for the other return.
Traditional Valance Installation
Step 1A
Attach the valance to the headrail (outside-mount)
Center the front panel with the headrail.
Slide the mounting tab on the front valance panel into the valance clips until they click into place.
Step 1B
Attach the valance to the headrail (inside-mount)
Center the front panel with the headrail.
Slide the mounting tab on the front valance panel into the valance clips until they click into place.
Transitional Valance Installation
Step 1A
Attach the valance to the headrail (outside-mount)
Center the front panel with the headrail.
Slide the mounting tab on the front valance panel into the valance clips until they click into place.
Step 1B
Attach the valance to the headrail (inside-mount)
Center the front panel with the headrail.
Slide the mounting tab on the front valance panel into the valance clips until they click into place.
Visions™ Valance Installation
Step 1
Install the clips on the valance
Install a valance clip about 2" in from each end. Space any remaining clips evenly along the length of the valance.
Insert the clip into the groove on the back side of the valance and then rotate the clip 90°.
Step 2
Attach the valance to the headrail
Hook the valance clips onto the front of the headrail. Make sure the hooks fit over the lip of the channel as shown.
Step 3
Attach the returns (outside-mount)
Slide a return “L” bracket into the angled end of each return.
Press the returns into place on each end of the valance.